Skip to searchSkip to main content

Steel & Iron Casting Foundry in Vijayawada, India

Bhanu Special Castings Pvt. Ltd. manufactures custom steel and iron castings from 0.5 kg to 2,500 kg per piece. We develop components from drawings, 3D models or physical samples.

Molten metal pouring from a ladle into a foundry mould

Foundry Capabilities at a Glance

Pattern development, sand moulding, induction melting, heat treatment, finishing and inspection.

Single-piece casting range

0.5–2,500 kg per piece

Production requirements

Development castings, replacement parts and repeat batches

Supply conditions

As-cast, fettled or heat-treated. Machining through partners.

Core foundry operations

CO₂ sand moulding, induction melting, heat treatment and inspection

Engineering support

3D CAD, scanning and reverse engineering. External casting simulation.

Materials

Steel and iron casting grades

Steel castings

Carbon & low alloy, manganese, heat-resistant, stainless, duplex and super duplex

Iron castings

High chrome, Ni-Hard, grey iron and SG (ductile) iron

Our Foundry Infrastructure

Pattern Shop & Core Box Development

We develop patterns and core boxes from approved drawings, CAD models or physical samples. The pattern forms the outer shape of the casting in the sand mould, while the core box forms the sand core used for internal passages and cavities.

During design, we allow for shrinkage as the metal cools and add machining allowance where a surface will be finished later. Draft helps the pattern release cleanly from the sand, and the parting line determines where the mould halves separate.

We select the pattern material based on component size, geometry and order quantity. For repeat batches, the same tooling helps reproduce the approved casting geometry.

Wooden pump casing pattern and matching core box

Casting Methoding & Engineering

We review the casting geometry, section thicknesses and material grade before moulding. That review guides where the metal enters the mould, where feeders are placed and how the cores are supported.

The gating system directs metal into the cavity. Feeders supply additional liquid metal as thicker sections solidify and contract. Their placement depends on how the casting fills and where it is likely to solidify last.

Where required, we use external casting simulation to assess mould filling and solidification. The results can guide changes to the gating or feeder layout before production.

Engineer reviewing a casting model and simulation

Sand Moulding & Core Making

We use sodium silicate CO₂ sand moulding, with green sand available for suitable parts. Mould selection depends on casting size, geometry and the features that need to be reproduced.

The pattern forms the outer cavity. Sand cores form internal passages, bores or recesses that the pattern alone cannot create. We position the cores in the mould so those features align with the casting geometry.

Before closing the mould, we check that the cavity is clean and that the cores are correctly seated. Correct positioning helps maintain the intended wall thickness around internal features.

Sand mould with a core seated inside

Induction Melting & Pouring

We melt the metal charge in an induction furnace. The charge and alloy additions are selected according to the specified steel or iron grade.

Before pouring, we test a sample with a spectrometer and compare the measured chemistry with the grade limits. Where an adjustment is needed, the result guides the alloy additions to the melt.

The metal is poured into the prepared moulds. Each heat has an identification number that links the castings to the melt and its chemistry records for traceability.

Induction furnace pouring molten metal

Heat Treatment

We select the heat-treatment cycle based on material grade, section thickness and the properties specified for the casting. The cycle may include annealing, hardening, quenching or tempering, depending on the material and application.

The heating, holding and cooling stages are set for the selected treatment. The aim may be to relieve residual stress or achieve the required balance of hardness, strength and toughness.

After treatment, we check against the agreed hardness or mechanical requirements. The specified tests depend on the grade, drawing and order requirements.

Steel castings on a heat-treatment furnace trolley

Fettling & Surface Finishing

After shakeout, we remove the gates and risers used during pouring and solidification. We dress the attachment points and remove flash or excess metal along the parting line where needed.

Shot blasting or grinding removes adhering sand and scale and prepares the surface for visual inspection. Finishing requirements depend on the casting geometry and the agreed supply condition.

When the drawing calls for machined faces, bores or other finished dimensions, we coordinate machining through our partners.

Foundry worker grinding the surface of a steel casting

Quality Assurance & Inspection

Inspector measuring a casting with a caliper
Spectrometer analysis
Grade chemistry.
Hardness testing
Specified hardness range.
Tensile testing
Strength and elongation.
Dimensional inspection
Drawing dimensions and tolerances.
Microstructure examination
Specified metallurgical characteristics.
Ultrasonic testing (UT)
Internal discontinuities where applicable.
Magnetic particle inspection (MPI)
Surface and near-surface discontinuities in suitable ferromagnetic materials.

Heat numbers support traceability. Material test documentation can be provided as agreed.